IPC Standards Committee Reports – Component Traceability, Base Materials, Fabrication Processes, Assembly and Joining
December 1, 2015 | IPCEstimated reading time: 5 minutes
The 5-22arr J-STD-001/Conformal Coating Material & Application Industry Assessment Task Group discussed the current status of round robin testing.
The 5-22as Task Group met to discuss an addendum to 5-22as, Space Applications Electronic Hardware Addendum to IPC J-STD-001F Requirements for Soldered Electrical and Electronic Assemblies.
The 5-22f IPC-HDBK-001 Task Group celebrated the completion of the forthcoming revision to IPC-HDBK-001, Handbook and Guide to Supplement J-STD-001, and discussed opening the document for an amendment to address changes as a result of J-STD-001F, Am 1.
The 5-23a Printed Circuit Board Solderability Specifications Task Group reviewed all comments submitted on the Amendment 1 to the J-STD-002D, including the substantial number from Jim Daggett of Raytheon.
The 5-23b Component and Wire Solderability Specification Task Group reviewed some potential changes to J-STD-003C that may just allow the people from DSCC to accept what could be the revision D of this standard.
The 5-24a Flux Specifications Task Group reviewed the SIR test method verification plan, including comparing the current J-STD-004 plan with the IEC round robin plan to determine the test board preparation procedures, specify the testing protocol and set the timing for the testing.
The 5-24b Solder Paste Task Group reviewed testing of solder balls, paste wetting and tackiness (tack) plus discussed rheometry testing using both parallel plate and spiral pump viscometers.
The 5-24c Solder Alloy Task Group discussed the addition of one more patented lead free alloy to J-STD-006; the best way to address the addition of rare earth elements to lead free alloys and then discussed three IPC TM-650 test methods that will be placed in the 5-24c TG KAVI site for additional discussion by members of the task group.
Page 2 of 2Suggested Items
Taiyo Circuit Automation Installs New DP3500 into Fuba Printed Circuits, Tunisia
04/25/2024 | Taiyo Circuit AutomationTaiyo Circuit Automation is proud to be partnered with Fuba Printed Circuits, Tunisia part of the OneTech Group of companies, a leading printed circuit board manufacturer based out of Bizerte, Tunisia, on their first installation of Taiyo Circuit Automation DP3500 coater.
Vicor Power Orders Hentec Industries/RPS Automation Pulsar Solderability Testing System
04/24/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, is pleased to announce that Vicor Power has finalized the purchase of a Pulsar solderability testing system.
AIM Solder’s Dillon Zhu to Present on Ultraminiature Soldering at SMTA China East
04/22/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce that Dillon Zhu will present on the topic: Ultraminiature Soldering: Techniques, Technologies, and Standards at SMTA China East. This event is being held at the Shanghai World Expo Exhibition & Convention Center from April 24-25.
AIM to Highlight NC259FPA Ultrafine No Clean Solder Paste at SMTA Wisconsin Expo & Tech Forum
04/18/2024 | AIMAIM Solder, a leading global manufacturer of solder assembly materials for the electronics industry, is pleased to announce its participation in the upcoming SMTA Wisconsin Expo & Tech Forum taking place on May 7 at the Four Points by Sheraton | Milwaukee Airport, in Milwaukee, Wisconsin.
Hentec/RPS Publishes an Essential Guide to Selective Soldering Processing Tech Paper
04/17/2024 | Hentec Industries/RPS AutomationHentec Industries/RPS Automation, a leading manufacturer of selective soldering, lead tinning and solderability test equipment, announces that it has published a technical paper describing the critical process parameters that need to be optimized to ensure optimal results and guarantee the utmost in end-product quality.