Arlon EMD and Doosan Electro-Materials BG to Exhibit at IPC APEX EXPO 2017
February 8, 2017 | Arlon EMDEstimated reading time: 1 minute
Arlon Electronic Materials, a specialty materials supplier based in Southern California, will be teaming up with Doosan Electro-Materials BG, at the IPC APEX EXPO 2017. Doosan will be promoting DS600 Flexible Copper Clad Laminates and DS7402, Halogen Free, High Tg FR-4 materials. Arlon will be highlighting the technological advantages of several specialty materials including the recently released, 85HP high performance polyimide system along with the reintroduction of multiple nonwoven aramid reinforced products.
Arlon’s recent distribution agreement with Doosan Electro-Materials BG will allow Arlon to provide sales and technical support of various products from Doosan. For Arlon EMD, this agreement enables expansion of product line offerings into the electronic materials industry, while enhancing Arlon’s focus on rigid-flex applications for military, avionics and space market segments.
The IPC APEX EXPO 2017 show will take place February 14th thru 16th, 2017 in San Diego, California. Arlon EMD and Doosan Electro-Materials BG will be located at booth # 3602.
About Arlon: Arlon EMD is a privately held, veteran owned, US manufacturer and distributor of specialty materials. Arlon has supplied materials for the N. American, UK and European markets for more than 25 years from their manufacturing location in Rancho Cucamonga, California.
For additional information, please visit our website.
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.