Made in Brazil: The Evolution and Revolution of Impedance Control in PCB Production
July 21, 2016 | Renato Peres, Circuibras Circuitos Impressos ProfissionaisEstimated reading time: 1 minute
The PCB industry in Brazil has gone through several changes over the last decade. Our customers have been demanding better quality and higher-reliability products more than ever before, but few things have changed as much as impedance control. PCBs with impedance control requirements have become the engine of the market, and finding solutions to fit the customer’s needs is extremely challenging.
Ten years ago, the Brazilian PCB industry was a little vague on this subject, and very few PCB shops were doing impedance testing. About five years ago, with the evolution of the national PCB industry, customers started producing prototypes requiring impedance control and the market started to develop. However, it seemed to me that neither the customers nor the PCB shops really knew what to order and to deliver at that time.
There always were differences between the specs for the board, the coupon measured, and the simulation software. As a best practice, many PCB shops used to appeal to a cross-section analysis to verify the PCB build up. In the end, impedance simulation software was more reliable than the TDR measurements.
I remember I felt a bit normal last year when I read the article written by Dan Beaulieu and Bob Tarzwell for The PCB Design Magazine, "Controlled Impedance: A Real-World Look at the PCB Side." Coupons that don’t fit the specs of the customers, cross-section analyses, differences in resin flow during lamination, copper thickness variation, and many other issues described in the article were very similar to the problems we faced daily.
Nevertheless, the industry in Brazil has gone further, pressing the suppliers to develop new controls, not yet usual to the national market.
To read this entire article, which appeared in the July 2016 issue of The PCB Magazine, click here.
Suggested Items
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
AT&S Shines with Purest Copper on World Recycling Day
03/18/2024 | AT&SThe Styrian microelectronics specialist AT&S is taking World Recycling Day as an opportunity to review the progress that has been made in recent months at its sites around the world in terms of the efficient use of resources: