Satellites Find Sustainable Energy in Cities
January 4, 2016 | KITEstimated reading time: 3 minutes
Underground heat islands in cities have an enormous geothermal potential. Warm groundwater can be used to produce sustainable energy for heating and cooling. Researchers of Karlsruhe Institute of Technology (KIT) have now developed a new method to find underground heat islands: They estimate groundwater temperature from surface temperatures and building densities measured by satellites.
In bigger cities, temperatures usually are far higher than in the rural surroundings. These so-called urban heat islands result from various factors, such as population density, surface sealing, thermal radiation of buildings, industry, and transport as well as lacking vegetation. This phenomenon affects the atmosphere, surface, and subsurface of modern cities.
Temperature anomalies may contribute to regional air pollution and an increased mortality during hot spells in summer. Increased groundwater temperatures influence underground ecosystems and may favor growth of pathogens in groundwater. But underground heat islands also have high potentials for energy supply and climate protection: Energy from close-to-surface groundwater aquifers may be used for heating in winter and cooling in summer with the help of geothermal or groundwater heat pumps. If this geothermal potential would be used, part of the growing energy consumption of cities might be covered. This would reduce emission of greenhouse gases and, thus, counteract global warming.
Surface and underground heat islands are connected mainly by thermal conduction. So far, research has studied the individual heat islands separately from each other, such that little is known about interactions and relationships between above-ground and underground temperatures. A group of scientists of the Institute of Applied Geosciences (AGW) and the Institute of Meteorology and Climate Research – Atmospheric Trace Gases and Remote Sensing Division (IMK-ASF) of KIT as well as of ETH Zurich recently analyzed above-ground and underground heat islands in four big cities in Germany in relation to each other. The results are reported in the journal “Environmental Science & Technology”.
The scientists used satellite measurements of surface temperature to easily determine spatial and temporal parameters of above-ground heat islands. Description of underground heat islands is much more difficult. Interpolation of groundwater temperature measurements at existing monitoring stations is time-consuming and expensive. For this reason, other methods are required. The researchers of KIT and ETH compared above-ground and underground heat islands in the four cities of Berlin, Munich, Cologne, and Karlsruhe. They found a spatial correlation of up to 80%. Correlation in older cities, such as Cologne, exceeds that of relatively young cities like Karlsruhe. The older the city is, the more pronounced is underground warming. 95% of the areas studied were found to have a higher groundwater temperature than surface temperature. The scientists attributed this to additional underground anthropogenic heat sources, such as cellars of buildings, sewers, or points of reinjection of cooling water.
Hence, satellite-measured surface temperature alone is not sufficient to reliably estimate groundwater temperature. For this reason, the scientists also considered population density and cellar temperature. They succeeded in estimating regional groundwater temperatures with a mean absolute error of 0.9 Kelvin. “This method can be applied for a first assessment of underground heat islands and, hence, of ecological conditions in the groundwater and of the geothermal potential. No complex groundwater temperature measurements and interpolations are required,” Philipp Blum, Professor for Engineering Geology of AGW, KIT, explains. Page 1 of 2
Suggested Items
Real Time with… IPC APEX EXPO 2024: Exploring the Future of Surface Finishes
04/25/2024 | Real Time with...IPC APEX EXPOJoe McGurran, product marketing director for MKS Atotech, looks into the future of surface finishes, discussing less nickel, reduced thickness, technologies influencing HDI and UHDI, and the benefits of nickel-free surface finishes. He also touches on popular finishes like ENIG and palladium immersion gold and discusses the value proposition of making a change.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
IDTechEx Report Unveils 3D Electronics Status and Opportunities
04/22/2024 | PRNewswire3D electronics is an emerging manufacturing approach that enables electronics to be integrated within or onto the surface of objects. 3D electronic manufacturing techniques empower new features, including mass customizability, greater integration, and improved sustainability in the electronics industry.
NASA, Japan Advance Space Cooperation, Sign Agreement for Lunar Rover
04/11/2024 | NASANASA Administrator Bill Nelson and Japan’s Minister of Education, Culture, Sports, Science and Technology (MEXT) Masahito Moriyama have signed an agreement to advance sustainable human exploration of the Moon.
Lockheed Martin Conducts Historic LRASM Flight Test
04/04/2024 | Lockheed MartinThe U.S. Navy in partnership with Lockheed Martin [NYSE: LMT] successfully conducted a historic Long-Range Anti-Ship Missile (LRASM) flight test with four missiles simultaneously in flight.