Understanding MIL-PRF-31032, Part 4

Reading time ( words)

Continuing with Part 4 of the discussion on understanding the military PCB performance standard MIL-PRF-31032, the next step in the process is to create four new procedures to address the unique requirements of the military.

Qualification and Add-On Procedure
This process provides the guidelines for the initial qualification of the company, as well as a path for future add-on qualifications. The first thing that needs to be included is the process for developing the qualification test vehicle. This is the specific PCB design that will be used to build the qualification boards. The documentation required must also be identified, such as production traveler, test vehicle design, drawings, multilayer layup, etc.

Test Vehicle
A company will qualify for specific technology and will need to develop a qualification test plan, which is a document that specifies the following minimum attributes of the qualification board:

  • Max. Number of Layers and Dielectric Type
  • Max. Panel Size
  • Max. Board Thickness
  • Min. Drilled Hole Before Plating
  • Aspect Ratio
  • Min. Conductor Width
  • Via Structure
  • Min. Conductor Space
  • Hole Preparation
  • Hole Wall Conductive Coating
  • Copper Plating
  • Solder Resist
  • Silkscreen
  • Final Finish
  • Additional Fabrication Capabilities
  • Controlled Impedance

It is important to note here that the qualification “flows down” but not “up.” In other words, if an 18-layer is qualified, layer counts less than 18 layers can be built as long as the other above parameters are the same, but a 20-layer would not be allowed.

Sample Size and Data Requirements
The next section would be to establish the lot size of the qualification lot and the sample sizes that will be used for testing. The data recording and retention of all qualification records must be defined, including coupons and any extra boards left over from the qualification lot.

Failure Analysis and Resubmission
A DLA-approved third-party testing lab must be selected to use for the initial qualification as well as the ongoing monthly testing. Should a submitted sample fail any tests, this procedure needs to have a provision for failure analysis and corrective action. This typically leverages the existing processes already in place. The rules for resubmitting new qualification boards must also be defined here, particularly that additional extra samples from the failed lot cannot be used.

Qualification Test Summary and Reporting
This section outlines the components for the summary that is needed to be submitted to the DLA after all tests and inspections have been successfully performed, including the third-party lab). This includes things like the travelers, internal and external test and inspection results, lot conformance forms and results, failure mode for any rejections, dimensional and electrical test parameters and measurements, and a copy of the qualification test plan.

Add-On Qualification
MIL-PRF-31032 allows for the expansion of the qualified technology through the add-on qualification process. A technology that falls within 25% of the current qualified technology can be built with a new qualification test plan and TRB approval. For example, with a qualified 18-layer, a 22-layer could be qualified through the add-on process.

The same would apply to line width, hole size, etc. There is no need to wait for DLA approval in these cases; they will verify the add-on qualification data during their next regular visit/audit. Anything greater than a 25% technology change will require a new full qualification like the initial qualification.

This wraps up qualification and add-on procedures. Part 5 will focus on the next unique procedure needed to produce MIL-PRF-31032 PCBs.

Editor’s note: Read Part 1Part 2, and Part 3.

Anaya Vardya is president and CEO of American Standard Circuits; co-author of The Printed Circuit Designer’s Guide to… Fundamentals of RF/Microwave PCBs and Flex and Rigid-Flex Fundamentals; and author of Thermal Management: A Fabricator's Perspective. Visit I-007eBooks.com to download these and other free, educational titles. He also co-authored “Fundamentals of PCB Technology.”


Suggested Items

Excerpt Chapter 5: 'The Printed Circuit Designer’s Guide to... Thermal Management with Insulated Metal Substrates, Vol. 2'

08/09/2022 | Didier Mauve and Robert Art, Ventec
Chapter 5 of the 2nd Volume from The Printed Circuit Designer's Guide to... Thermal Managment with Insulated Metal Substrates provides examples of thermally enhanced prepregs and cores now available in the market with the versatility to solve a wide variety of challenges. Included in this chapter you will find examples of simple designs and more complex hybrid assemblies that combine multilayer and single-layer areas on the same board.

Understanding MIL-PRF-31032, Part 6

12/08/2020 | Anaya Vardya, American Standard Circuits
Concluding this six-part discussion on understanding the military printed circuit board performance standard MIL-PRF-31032, Anaya Vardya the remaining procedure required to address the unique requirements of the military.

Additive Electronics TechXchange: NSWC Crane and Lockheed Martin Presentations

10/27/2020 | Happy Holden, I-Connect007
The Additive Electronics TechXchange this year was a virtual event. Happy Holden covers two presentations, including “Very High-Density Investigation Project” by Steve Vetter of the NSWC Crane Naval Facility and "Electronics Additive Manufacturing for Defense and Space" by Kourtney Wright, Ph.D., of Lockheed Martin Advanced Technology Center.

Copyright © 2022 I-Connect007. All rights reserved.