ACM Research Introduces Thin Wafer Cleaning System
September 15, 2020 | Globe NewswireEstimated reading time: 3 minutes
ACM Research, Inc, a leading supplier of wafer-processing solutions for semiconductor and advanced wafer-level packaging (WLP) applications, announced the introduction of its Thin Wafer Cleaning System, a high-throughput, four-chamber system designed for single-wafer wet processes including cleaning, etching and surface finishing. The system is intended for the manufacture of both MOSFET and insulated-gate bipolar transistor (IGBT) devices for the power semiconductor market, and features complete touch-free handling and processing based on the Bernoulli effect to eliminate possible wafer damage and improve final device yield. It supports 200mm and 300mm Si wafers and is suitable for Taiko wafers down to 50-micron thickness, ultra-thin wafers of less than 200-micron thickness, high aspect ratio (>10:1) deep trench wafers as well as double-thickness bonded wafer pairs.
Modor Intelligence, a market research consulting firm, expects the IGBT market to increase from US$5.4 billion in 2019 to US$9.4 billion in 2025, based on the broad application range of IGBTs to modern appliances such as cookers, microwaves, electric cars, trains, variable-frequency drives, variable speed refrigerators, air conditioners, lamp ballasts, municipal power transmission systems and stereo systems. Modor Intelligence also reports that sales of electric cars in Europe, North America and China are creating new avenues for IGBTs to support infrastructure and for manufacturing electric vehicles.1
Furthermore, keeping up with the miniaturization trend while improving device performance has sparked demand for smaller pitch, deeper trench and thinner wafers. Yole Développement, a market research and technology analysis firm, predicted the market for thinned wafers will increase from 100 million in 2019 to 135 million in 2025, a compound annual growth rate (CAGR) of more than 5%. Yole Développement expects this market growth to be driven by memory, CMOS image sensors and power silicon carbide components as well as LED and laser diodes.2
“To compete for market share, power device manufacturers must expand their MOSFET and IGBT manufacturing lines to include wafer thinning equipment, without significantly increasing the overall fab footprint,” said David Wang, ACM’s Chief Executive Officer and President. “We have responded by developing a four-chamber tool that offers much higher throughput than the currently-available two-chamber systems. Additionally, we outfitted the tool with a proprietary contactless handling and processing system to prevent these fragile wafers -- which can be as thin as 50-microns -- from being damaged during the backside thinning and cleaning processes, thereby increasing overall device yield.”
ACM’s Thin Wafer Cleaning System has been designed to meet manufacturers’ needs. After mechanical grinding/polishing is performed to achieve desired thickness, the handling system supports these ultra-thin, high-warpage wafers throughout subsequent critical processes, including silicon thinning using a wet-etch step to eliminate microcracks. Additionally, by implementing a different combination of chemistries, the tool can be used for cleaning, photoresist removal, thin film removal and metal etching.
The tool’s handling system is programmable to accommodate deep trench, Taiko, ultra-thin wafers or bonded wafers. The robot arms for loading and unloading, as well as the chuck, have been designed for non-contact wafer handling using a proprietary method based on the Bernoulli effect. Nitrogen gas (N2) provides constant pressure to keep the wafer floating in place on the arm, which can be flipped for processing on either side while still holding the wafer in place. This allows for handling high-warpage wafers without contact.
During the wet process, the wafer sits front-side down on a Bernoulli chuck, where an N2 flow cushions the wafer, protecting it and keeping it dry. This proprietary design, using ACM’s patented technology on a Bernoulli chuck, features a recipe-controlled gap between the wafer and chuck to meet requirements for undercut width control on the wafer device side edge and pin mark-free control. Additionally, the system can be configured to include an optional thickness measurement function.
Each chamber can be configured with up to four swing arms for delivering process chemistries such as wet etchants, solvents, RCA cleaning chemicals, deionized water and nitrogen. Additionally, the chambers are designed to allow reclaiming of two types of chemicals.
ACM delivered its first Thin Wafer Cleaning System to a China-based analog/power semiconductor manufacturer in the second quarter of 2020, with revenue recognition subject to qualification and acceptance.
Suggested Items
Real Time with... IPC APEX EXPO 2024: Exploring Silicone Solutions with R&D Director of CHT
04/17/2024 | Real Time with...IPC APEX EXPOIn this interview, Gerry Ellis, the R&D director for CHT, discusses the product range offered by his company. He explains the challenges in creating base formulations, the drive to make products more user-friendly, and the various application techniques involved. Ellis also highlights the key market segments and the significance of providing efficient solutions to customers.
Gartner Forecasts Worldwide IT Spending to Grow 8% in 2024
04/17/2024 | Gartner, Inc.Worldwide IT spending is expected to total $5.06 trillion in 2024, an increase of 8% from 2023, according to the latest forecast by Gartner, Inc. This is an increase from the previous quarter’s forecast of 6.8% growth and puts worldwide IT spending on track to surpass $8 trillion well before the end of the decade.
Catching Up With Chasom Electronics
04/16/2024 | Dan Beaulieu, D.B. Management GroupI recently met with Chasom Electronics’ founding director Anil Kumar. Chasom offers a unique menu of services for companies looking to extend their technology capabilities on a short- or long-term basis. Read on to learn about this very unique service company.
Cicor Records Solid Growth in Q1
04/16/2024 | CicorThe Cicor Group continued to grow in the first three months of the year. Quarterly sales increased by 11.8% to CHF 107.3 million compared to the first quarter of the previous year (Q1/2023: CHF 96.0 million).
Real Time with... IPC APEX EXPO 2024: A Strategic Market Realignment
04/16/2024 | Real Time with...IPC APEX EXPOMarcy LaRont hosts Thomas Kunz of Schmoll Maschinen GmbH and Kurt Palmer of newly formed Schmoll America to discuss the strategic changes and developments at Schmoll with their departure from Burkle North America in this Real Time with... IPC APEX EXPO 2024 video interview.