aveni Extends Copper Interconnects to 5nm and Below
December 12, 2017 | Globe NewswireEstimated reading time: 2 minutes
aveni S.A. announced it has obtained results that strongly support the continued use of copper in the back end of line (BEOL) for advanced interconnects, at and beyond the 5nm technology node.
“In this 20th-anniversary year of copper integration, our results validate the comments made by IBM Research Fellow Dan Edelstein in his keynote presentation at the recent IEEE Nanotechnology Symposium, discussing that copper integration is here to stay,” noted Bruno Morel, aveni CEO.
As devices inevitably continue to shrink to meet (and create) market demand, designers are exploring alternative integration schemes, not only for the front end of line, but also the BEOL. This includes, most notably, replacing the copper in dual-damascene interconnects, to compensate for the increased resistance-capacitance (RC) delay that accompanies the thinner copper wires and adversely affects device speed. Proposed replacement options for copper are cobalt, the most likely candidate, or more exotic materials like ruthenium, graphene or carbon nanotubes.
Advanced dual-damascene structures employ an atomic layer deposition tantalum nitride (TaN) copper diffusion barrier, a thin chemical vapor deposition (CVD) cobalt liner, and the electroplated copper fill layer, which makes up most of the wiring. Earlier generations (≥7nm node) also use a physical vapor deposition (PVD) copper seed layer between the cobalt and copper fill, but advanced devices are phasing out this film due to marginal seed coverage and integration hurdles.
Of particular interest is the thin TaN barrier, which prevents copper from diffusing into and poisoning the device. The integrity of the thin cobalt liner (on top of TaN) is critical to ensuring that the barrier functions properly. The reduced thickness of cobalt liners for the 5nm technology node is approaching 3nm, reducing process flexibility for conventional approaches to copper plating.
In a recent study, aveni compared its Sao™ alkaline-based copper electroplating chemistry performance with a conventional, commercially available acidic copper plating chemistry. The samples to be plated were 3nm CVD cobalt over TaN. The study results showed that the acidic copper chemistry attacked the cobalt liner, causing the plating chemistry to react with the underlying TaN film and form tantalum oxide (TaOx). TaOx formation is another failure mode of devices, because it creates an effective open circuit that prevents current flow.
With aveni’s Sao chemistry, the cobalt remained intact and TaOx was not formed, which enables the extension of copper interconnects to process nodes at 5nm and below.
Frédéric Raynal, chief technical officer at aveni, commented, “We were extremely excited about these results, because they substantiate our position that Sao alkaline-based chemistry for copper electroplating is superior to acidic chemistries, especially with the thinner cobalt liners used in advanced nodes.”
aveni will publish the complete findings in a report in early 2018.
About aveni S.A.
aveni is the leading developer and supplier of Electrografting™ chemistries and processes for the semiconductor and electronics industry. Headquartered in Massy, France, the company has a worldwide reputation for providing transformative chemistries and processes, coupled with the technology transfer capability to enable smooth transitions of its solutions into production. For more information, click here.
Suggested Items
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.
Trouble in Your Tank: Supporting IC Substrates and Advanced Packaging, Part 5
03/19/2024 | Michael Carano -- Column: Trouble in Your TankDirect metallization systems based on conductive graphite or carbon dispersion are quickly gaining acceptance worldwide. Indeed, the environmental and productivity gains one can achieve with these processes are outstanding. In today’s highly competitive and litigious environment, direct metallization reduces costs associated with compliance, waste treatment, and legal issues related to chemical exposure. What makes these processes leaders in the direct metallization space?
AT&S Shines with Purest Copper on World Recycling Day
03/18/2024 | AT&SThe Styrian microelectronics specialist AT&S is taking World Recycling Day as an opportunity to review the progress that has been made in recent months at its sites around the world in terms of the efficient use of resources: