DELO: New Semicon Adhesive Propels Autonomous Driving Forward
October 20, 2023 | DELOEstimated reading time: 1 minute
DELO has developed a flexible electronics adhesive that permanently seals sensor housings airtight and thus reliably protects components such as image sensors. DELO DUALBOND BS3770 meets the stringent requirements of the semiconductor and automotive industries and helps drive innovation in autonomous driving.
The autonomous driving trend comes with ever-stricter safety requirements. Therefore, reliable components such as image sensors are installed in LiDAR and RADAR systems. Sensor housings on PCBs must be hermetically sealed throughout their entire service life in order to maintain their function permanently without interruption. However, previous solutions for hermetically sealing the housing and filter glass are reaching their limits due to these stricter requirements, failing to withstand the tests of the automotive industry, according to standard AEC-Q100.
DELO has developed DELO DUALBOND BS3770, a special electronics adhesive for semiconductor manufacturers to meet the demanding reliability and qualification tests of automotive suppliers.
Unlike adhesives previously available on the market, the newly developed adhesive is a flexible product with a Young's modulus of less than 5 MPa at room temperature. Due to its flexible properties starting from a temperature as low as approximately -50 °C, the adhesive can compensate for pressure changes that occur, such as those caused by temperature changes, humidity differences, or heat input in the reflow process during production. As a result, defects such as pop-ups or delamination do not occur, and the sensor is permanently protected.
DELO DUALBOND BS3770 can be precisely applied by needle dispensing while maintaining narrow and high bondlines. Curing takes place in two consecutive steps using UV light and heat. After dispensing, the adhesive is fixed in a few seconds by means of classic light fixation. Alternatively, it can be transferred to the B-stage, which is particularly relevant for bonding filter glasses with blackprint. At this stage, it achieves an initial adhesion comparable to tape. Afterwards, the second component can be joined. Thanks to the adhesive’s initial adhesion, the component is directly fixed so that it can be entirely processed further. Final curing takes place in a convection oven at +150 °C within 40 minutes.
In addition to image sensors for LiDAR and RADAR applications, DELO DUALBOND BS3770 is also used in driver monitoring and for 5G applications.
Suggested Items
Material Insight: The Dielectric Constant of PCB Materials
05/17/2024 | Dr. Preeya Kuray -- Column: Material InsightIn the world of PCB design, miniaturization can be achieved by using low dielectric constant (Dk) materials. Low Dk materials can allow for a reduction in thickness while maintaining a given trace width, leading to lower transmission loss and higher density circuitry.
Do You Think Enough About Ergonomics?
05/15/2024 | Barry Matties, I-Connect007Vitorio Lorenzini, a workstation design expert with Assembled Product Specialists, discusses the importance of ergonomics in the workplace. He emphasizes the value of early involvement in workstation planning to optimize space and resources, ultimately enhancing workflow efficiency.
Using AI to Redefine Productivity
05/15/2024 | Nolan Johnson, SMT007 MagazinePlato Systems, a machine perception company spun out of Stanford University, employs AI and video data to analyze and optimize the human component in manufacturing. Initially focused on semiconductors, Plato Systems has expanded into EMS manufacturing. Co-founder and CEO Amin Arbabian, along with product advisor Anders Holden and head of growth Luis Vidal, discuss their approach to changeover optimization and its impact on productivity in the industry. They’ve also included customer Raj Vora in the conversation.
Standard of Excellence: Collaboration—The Right Path to Innovation
05/15/2024 | Anaya Vardya -- Column: Standard of ExcellenceNow more than ever, as new and innovative technologies for printed circuit boards are in demand, we need collaboration between PCB designers, fabricators, and assemblers. Close partnerships with PCB designers and assemblers are key to developing and producing PCBs with boards with new and innovative technology. These collaborative partnerships, along with the partnership with the end customers, are more critical than ever before.
Viscom’s Approach to Inline X-Ray
05/14/2024 | Barry Matties, I-Connect007In this interview, Viscom President Ed Moll and CEO Jesper Lykke discuss the importance of inline X-rays for real-time data and board inspection. They also discuss AI integration, customer inquiries, and ROI considerations. Also, as Ed moves into semi-retirement, he reflects on his long career, recent developments, and the evolving X-ray industry. He shares his insights on career opportunities for emerging engineers in the industry.