Rogers Launches TC350 Plus for Higher-Power Microwave, Industrial Heating
June 3, 2019 | Rogers CorporationEstimated reading time: 1 minute
Rogers Corporation introduces TC350 Plus laminates. TC350 Plus laminates are ceramic filled PTFE-based woven glass reinforced composite materials providing a cost effective, high performance, thermally enhanced material for the circuit designer. With a thermal conductivity of 1.24W/mK, this next generation PTFE-based laminate is ideally suited for higher power microwave and industrial heating applications requiring higher maximum operating temperatures, low circuit losses, and excellent thermal dissipation within the circuit board. Additionally, the advanced filler system used enables the composite to have much improved mechanical drilling performance when compared with other competitive laminates. This will result in lower manufacturing costs during circuit board fabrication.
The standard TC350 Plus laminates are offered with a smooth (Rq= 1.0µm) electrodeposited copper foil cladding to reduce insertion loss and RF heating of conductors within the circuit. Resistive foil and metal plate options are available upon request. TC350 Plus laminates are available in thicknesses from 0.010” to 0.060” to address higher power design needs.
The woven glass reinforcement combined with the high filler content of the laminate affords excellent dimensional stability. Other key features of the laminate include low z-axis CTE (38ppm/°C) for excellent plated through hole reliability, low loss tangent of 0.0017 at 10 GHz to enable low loss designs, low moisture absorption of 0.05% to ensure stable performance in a range of operating environments, high dielectric strength of 650 V/mil to ensure good z-axis insulation between conductor layers, and UL 94 V-0 flammability performance to enable the use of the material in commercial applications.
TC350 Plus laminates are used in a range of applications including Amplifiers, Combiners, Power Dividers, Couplers, and Filters. Applicable markets range from Commercial and Consumer to Defense and Aerospace.
About Rogers Corporation
Rogers Corporation is a global technology leader in engineered materials to power, protect, and connect our world. With more than 180 years of materials science experience, Rogers delivers high-performance solutions that enable clean energy, Internet connectivity, advanced transportation and other technologies where reliability is critical. Rogers delivers Power Electronics Solutions for energy-efficient motor drives, vehicle electrification, and alternative energy; Elastomeric Material Solutions for sealing, vibration management, and impact protection in mobile devices, transportation interiors, and performance apparel; and Advanced Connectivity Solutions materials for wireless infrastructure, automotive safety and radar systems. Headquartered in Chandler, Arizona (USA), Rogers operates manufacturing facilities in the United States, China, Germany, Belgium, Hungary, and South Korea, with joint ventures and sales offices worldwide. For more information, visitwww.rogerscorp.com.
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.