EU Commission Launches Stakeholder Consultation on RoHS Exemptions
September 20, 2017 | IPCEstimated reading time: 1 minute
The European Union (EU) Commission launched a four-week stakeholder consultation on DRAFT Delegated Directives for exemptions:
- 6(a) Lead as an alloying element in steel for machining purposes and in galvanized steel containing up to 0.35% lead by weight
- 6(b) Lead as an alloying element in aluminum containing up to 0.4% lead by weight
- 6(c) Copper alloy containing up to 4% lead by weight
- 7(a) Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead)
- 7(c)-I Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound
- 18(b) Lead as activator in the fluorescent power of discharge lamps containing phosphors
- 24 Lead in solders for the soldering to machined through hole discoidal and planar array ceramic multilayer capacitors
- 34 Lead in cermet-based trimmer potentiometer elements
The consultation closes on October 17, 2017.
IPC, in conjunction with an international industry stakeholder group, applied for more than a dozen exemption extension requests under the EU RoHS Directive. The RoHS2 Directive dictates expiration dates for all exemptions granted and several critical to the electronics manufacturing industry were set to expire by July 21, 2016. However, all exemptions for which industry submitted a renewal application will not expire until the EU Commission completes the current ongoing review of the applications.
Throughout the process, IPC and several member companies provided important technical information in order to ensure the extension requests are robust and scientifically sound. IPC reviewed all extension requests and provided important feedback that resulted in credible material submitted to the EU Commission.
IPC’s EHS Committee and RoHS Exemptions Task Force will review the draft delegated acts and develop a response to the stakeholder consultation. IPC member companies are also encouraged to comment directly to EU Commission through their website.
Suggested Items
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.
ENNOVI Introduces a New Flexible Circuit Production Process for Low Voltage Connectivity in EV Battery Cell Contacting Systems
04/03/2024 | PRNewswireENNOVI, a mobility electrification solutions partner, introduces a more advanced and sustainable way of producing flexible circuits for low voltage signals in electric vehicle (EV) battery cell contacting systems.
Heavy Copper PCBs: Bridging the Gap Between Design and Fabrication, Part 1
04/01/2024 | Yash Sutariya, Saturn Electronics ServicesThey call me Sparky. This is due to my talent for getting shocked by a variety of voltages and because I cannot seem to keep my hands out of power control cabinets. While I do not have the time to throw the knife switch to the off position, that doesn’t stop me from sticking screwdrivers into the fuse boxes. In all honesty, I’m lucky to be alive. Fortunately, I also have a talent for building high-voltage heavy copper circuit boards. Since this is where I spend most of my time, I can guide you through some potential design for manufacturability (DFM) hazards you may encounter with heavy copper design.